Colecago's Blog » Bucketworks, Buildathon, Hackathon, HandsOn, Health, Healthcare, Project, Tech

BuildHealth Recap

I figured I would write a better Buildhealth wrapup than just the videos I posted.

 

First of all, I have a playlist for the Buildhealth videos, see them here

Planning:

I heard about the Buildathon from Sector67′s Google Group.  I talked to some friends about forming a team.  A few weeks prior I was thinking about not going, then Meg re-insisted I should go after the April 3rd Sector67 meeting where Mark brought up the Buildathon.  I talked to my team, they were still on and we signed up for some Google + chats to discuss ideas.  I knew from the beginning I wanted to do hardware, but not sure what yet.  We had a Google + hangout later that week to discuss.  I had an idea about making a rumble belt for deaf people that took in several audio inputs on a necklace or collar type of device and rumbled with the intensity, frequency, and direction of the sound.  I still think this is a great idea, but it doesn’t really fit healthcare.  I forgot all about the Google + hangout on Monday to discuss and apparently everyone else did too.  I recapped with them later in the week and because of conflicts, all of my teammates dropped out (had 2 guaranteed, 1 never heard from, and 1 possible).  I was considering not going, and then I decided I should go even if I couldn’t build hardware just to support another team.  On Thursday night I had this great idea of a UV System to kill germs.  I told my team I was still going and started making preparations and getting supplies.  I borrowed a Roomba and some random parts from Sector67.  Then I got some messages from Steve saying he was back in.  We planned on and off the rest of the day for our ideas and packed that night to leave.

 

Arrival:

We arrived at 9am and parked the car.  Tim introduced himself to us and then showed us the upstairs where we could put our stuff.  Steve and I moved a table into our empty room and then unloaded my car into the room.  I had a  lot of hardware supplies and tools.  After unpacking we ate some breakfast and sat at a table with fellow buildathoners and talked a little bit while we waited for it to start.  A little over 40 people showed up, but not all were participants in the challenge.

 

Introductions:

The buildathon started with some basic introductions of the organizers as well as talking about the space and goals for this event.  We broke into small groups and did introductions.  Then Tim Bartholow talked about some staggering health care numbers.  After the data was gone over, the submitted problems were explained.  Some of the people that submitted problems were actually present, so they explained them.  As Steve and I had an idea beforehand for a solution, I gave a short description of the problem and solution we wanted to work on.  Then everyone broke into groups to discuss the submitted problems.  No one joined us at this point and Tim released us to go work on our problem/solution.

 

Designs and Lunch:

We sat in our rather warm glass room and worked on some designs.  I would take care of the Roomba and all involved with that and Steve would do the ceiling unit and the rotating reflector unit.  We ate some lunch, then continued designing.  A journalist from the Journal Sentinel stopped by and interviewed Steve and I about the buildathon and our idea.  After she left, we finished up our shopping list and left to Menards.  It was about 2pm at this point.

 

Menards Trip:

We spent a long time at Menards.  First we got the lights, Steve picked out Daylight CFLs as they are bright and produce whiter light than incandescents.  We picked up some wire, and then some low voltage halogens for the Roomba.  Next we needed hardware for the rotator.  Steve found some lazy suzan hardware near the castors and we found some vacuum belts with help from the associates.  We also got some wooden dowels, nuts and bolts, and some sliding door handles which were originally going to be used just to trace a circle on our cardboard for the rotator.  We picked up some reflective cardboard for the rotator, and got some much needed duct tape and industrial velcro.  We made it out of there $80 poorer.

 

New Member and Dinner:

When we came back, Alex was waiting for us.  He wanted to join our team so we explained what we wanted to do.  We tasked him with building the ceiling fixture.  I hooked the Roomba up to my power supply and turned it on to know what to expect.  You have to hit the power button, then hit the clean button.  I started taking it a part to hack into it.  Around dinner time we had two more people join us, Emily and Jesse, Emily researched current UV technologies and killing pathogens and Jesse helped build the cardboard topper for the lights on the Roomba.  I ate some dinner with Chris from Sector67 who stopped by and Tim Bartholow.  Then back to work on the Roomba.

 

Roomba Power:

Alex finished the ceiling unit and Steve was making good progress on the rotating unit.  He had a good base but was having trouble getting the belt to connect to the motor properly.  We decided to use the two sliding door handles/cups back to back as the pulley for the belt to ride on.  Our belts were too small and Menards didn’t have rubber bands (according to associates), so we duct taped them together.  I soldered wires on all the Halogen lights, which was pretty difficult as that metal didn’t like to solder, and then gave them to Jesse to put in his topper.  I then went to work on the power distribution of the Roomba.  I hooked up some wires to the Roomba’s main power, hooked some wires to a perf board and then to the two 7.4V batteries in series and a switch.  I powered up the Roomba and it worked fine.

 

Roomba Logic:

I needed a microcontroller on the Roomba to turn on all the relays, one for each light as they all draw close to an amp each, so four total, and also to act as a person pushing the buttons.  I traced out the buttons I needed, added some wires, I planned on sending a 0V signal to initiate the power on and clean sequence as the buttons were connected to ground.  For the lights, I tied the high side to the positive rail of the battery and the low side to the relay and the other side of the relay to ground.  The relays switch ground to the lights, completing their current path.  All 4 relays were switched on using using a single bjt as my micro couldn’t handle the current.  I had a lot of trouble getting this working.  I had a stable 5V and when I’d switch a relay, my power would die.  Mark from Sector came by and asked me how I was doing.  I explained my problem, how I switched out the regulator, bypassed the regulator, and I couldn’t figure out why it was failing.  He asked about my caps on my regulators.  I told him I didn’t have caps on them because I was running off of battery voltage and didn’t care about any ripple, I mean batteries make pretty clean power.  I tossed a cap on the regulator and problem solved.  Apparently regulators need a minimum capacitance or they go wacky, and not always apparently, because they could handle my micro alone.  Well this fixed all my problems, but in the end, I wasted so much time with testing and resoldering connections, I knew I couldn’t implement a wireless link.  I instead introduced a 10 second delay or so from switch on, to turning on the lights and Roomba function.  I then moved on to the spinning light control.

 

Rotating Light Logic:

I already had the code down for the delay and relay turn on, I tossed this code on another micro.  I found a 19V AC/DC convertor and hooked up another 5V regulator, this time with a cap, to power my micro.  I used a BJT to both turn on the AC powered light and another bjt to power the motor.  The motor spun really well at 5V so that’s what I used.  I then hooked the power supply up to a switch and tied the relay to the lights.  When I turned the switch, I waited 10 seconds and both the light and motor would start.  This part was done.  Steve did a great job getting this one working.

Ceiling Light:

This last light was the easiest.  I cut open another power supply as I planned on using another relay.  This relay was controlled by an inductive prox, our door sensor.  So I would turn the switch on, and then when the sensor sensed metal, it knew the door was shut and would turn the light on.  This worked pretty well.  Once all three systems were done, we went to bed.  I put our overnight videos on youtube and ended up going to bed at 4:30.

Morning Prep:

I woke up at 7:30 to begin our preparations.  I cleaned all of my equipment out of our little room and swept the floor and table.  I woke the guys up around 8 so we could install our system and work on our presentation.  We mounted the ceiling unit using yarn, put the Roomba on the floor, and put our secondary surface cleaner on the table.  We did a dry run of our system for our video here:

Alex and Steve had done most of the presentation the night before and this morning.  So we finished up the build slides and tried to come up with the intro.  Alex and Steve were to present most of the presentation and I just covered some of the build information.

 

Presentations:

We were the third group to present.  As we spent 90% of our time working on hardware, I felt like our research was lacking a bit, we didn’t know our market perfectly, but it went over well.  At the end, we took everyone over to our room and showed a demonstration.  All in all it went well.  All the groups finished their presentations, and all were good.  I especially liked Triage.me presentation, even though the presentation part was filled with technical difficulties, the actual content and idea was solid.  I really liked the website they put up and the text messaging service.  A big thanks to DC414 for helping out Triage.me and their presentation by remote desktopping into the mac and displaying to the projector through their laptop.  DC414 definitely were the hackers of the buildathon.

 

Results:

The judges consulted for a bit while a storm raged for a little bit outside.  We lost power for a little bit, so I grabbed the Roomba in case we needed a little roaming light.  They came back and presented the winning teams.  See the video here:

 

Reality Check won third place, Triage.me won second place, and we won first place and people’s choice.  This also included an invite to DC for the Health Datapalooza.  We took a picture with Ken from HHS, talked to the other groups and started packing our things to leave.

 

Conclusions:

Buildhealth was great.  I wasn’t expecting to do so well, and I’m glad I could do hardware.  Tim put on a great event and I can’t wait for the next one.  I met a lot of great people, from organizers and judges, to participants.  I don’t feel our idea was as hardhitting as the other guys, and I hope they were not discouraged to flesh out their ideas into full products.  DC is up in the air right now, waiting on word from HHS, this might not be the event for hardware guys such as us :-D  We’ll see, it would be a great opportunity.  I don’t currently see the light at the end of the tunnel for us starting our own business around this idea, but you never know.  This was my first Hackathon, but it won’t be my last.

 

 

 

Update: I’ve added the Teensy code below.  Pretty simple because its just a delay.  Wish I had gotten time to work on the wireless.  I do a lot of serial work so rolling a protocol wouldn’t have been super difficult.

TeensyBig

TeensySmall

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>